Selected subtotal: $6.07. Standard US shipping is $9.99 below $15, $7.99 from $15 to below $49, and free at $49 after discounts. Freight items excluded; other rates are shown at checkout.
AVAILABLE TO ORDER
✓SAME-DAY DISPATCH — ELIGIBLE IN-STOCK ORDERS BY 2 PM ET
✓STANDARD US SHIPPING — $9.99 BELOW $15 · $7.99 FROM $15 · FREE AT $49 AFTER DISCOUNTS
✓LOCAL PICKUP — FALL RIVER
✓NET-30 & PO — APPROVED ACCOUNTS
Economy Adhesive Trowel V-notch/SQ-notch
Official Hyde specifications
3/32" x 1/8" x 15/32" V-notch on 2 sides and 1/16" x 1/16" x 1/16" square notch on 2 sides
For special adhesive applications
PRODUCT FIT · IS THIS THE RIGHT TOOL?Straight answers. If it's the wrong tool for your job, we'll say so.
The guidance below describes applications and limitations. For a match to your particular job or an existing tool, ask us to confirm fit.
Not medium or large floor tile — neither the thin V nor the fine square lays the tall standing square ridges tile mortar needs (19050/19070).
Not a covering with a known single-notch trade answer — if the job is plainly medium tile, or plainly sheet vinyl, the dedicated single-profile trowel is the cleaner buy; the 19065 earns its place when the adhesive spec is unusual or shifting.
Not the offset perimeter run (19041) or the tapered confined-area work (19066) — it is a straight, square-cornered field blade.
And not old-floor removal: where old resilient goods or cutback adhesive underlie the work, the asbestos boundary governs the demolition, a test-before-you-disturb decision and never a job for a spreading trowel.
The 19065 is bought to meet printed adhesive specs, so the pail — not habit — decides V or square, and the coverage target the maker tested is the pass/fail. One direction, straight ridges on either profile — the air-escape rule governs a V film and a square bed alike; swirls trap air and cost you coverage. Angle near 45° and steady — the notch caps the deposit, the angle sets how much you lay; correct the angle before you distrust the notch. Confirm with a lift-and-read — pull a set piece before the adhesive skins and check the transfer against the adhesive maker's coverage number. Care for the carbon steel and both meters — dry after water-based adhesives; keep the fine square's small channels and the V's ridges clean, since cured adhesive in either quietly changes what that edge delivers. Treat the 15/32" figure with a physical check — it is unusually large for this notation, quoted as printed, and worth confirming on a real unit before any customer copy leans on it.
Asked before buying
BUYER QUESTIONS, ANSWERED BEFORE YOU ORDER
What is a "special adhesive applications" trowel actually for?
Meeting the notch a specialty adhesive prints on its label. It carries a thin V meter and a fine square meter so one tool covers a wider range of printed specs than a single-profile trowel.
Which edge do I use?
Whichever the adhesive label specifies — the V for thin, low-volume films, the fine square for a thin but fuller bed. Confirm by pulling a set piece and reading the transfer against the maker's coverage target.
Can I switch edges partway through a floor?
No — pick the meter the adhesive calls for and hold it for the whole covering. Two beds under one covering is a coverage defect. The two pairs of edges are for job-to-job range and for rotating to a clean edge, not mid-job changes.
Is the 15/32" measurement real?
It's quoted exactly as Hyde's row prints it, but it's unusually large for this notation, so we flag it for a physical-unit check and read it as the wide ridge spacing the line doc infers rather than asserting it as depth.
How is it different from the 19063?
The 19065's profiles and duty are printed on a Hyde catalog row; the 19063's U/V designation is store-title-only and unconfirmed. This is the combination trowel the line can specify today.
